Acid gold: a mildly acidic process that is used when plating from 7 to 200 mils of gold. The deposits are usually 23kt purity, and it is not usually used as the final finish.
Antique: a process which involves the application of a dark top coating over bronze or silver. This coating, either plated or painted, is partially removed to expose some of the underlying metal.
Anti-tarnish: is a protective coating that provides minimal tarnish protection for a low cost.
Barrel plating: is a type of mass finishing that takes place in a barrel or tub. Barrel plating is usually requested for very small pieces where pricing must be kept low.
Black nickel: is a bright or matte, dark plating process that is used to highlight antique finishes. Or, when used as a final color it will range from dark grey to light black. A bright black nickel will yield the darkest color.
Bright finish: a high luster, smooth finish.
CASS testing: the Copper-Accelerated Acetic Acid Salt Spray test is the same as the Neutral Salt Spray (NSS) test, except it is accelerated, with typical time cycles being 8 and 24 hours.
Cold nickel: is a non-brightened nickel bath which replicates the original finish, that is, bright areas remain bright and dull areas remain dull.
Color: describes the final top coating (flash) which could be white, silver, 14kt gold (Hamilton), 18kt gold, or 24kt gold (English gold). See “gold flash” and “cyanide gold.”
Copper: is an excellent undercoat in the plating process. Copper provides good conductivity and forms an excellent protective barrier between the base metal and the plate. There are three ways to plate copper: A copper strike promotes good adhesion and will activate the surface; a cyanide copper provides protection and good coverage, particular in pieces that have complex geometric shapes, and also promotes good adhesion; an acid copper levels the surface well, gives a very bright deposit, and can be used as a substitute for nickel.
Chromate: is a coating that provides moderate protection against tarnishing, primarily to enhance shelf-life.
Cross-sectional analysis: is a destructive test whereby an item is mounted in a plastic resin, then cut to expose a cross-section of the plate. The thickness of the plated layers are then measured under a microscope.
Cyanide gold: is used to apply the final coloration on gold. The thickness is usually no more than 3-5 mils. See “color” and “gold flash.”
Dark ruthenium: a grey, non-tarnishing, hard precious metal color which is in the same family as rhodium.
Dull finish: is a finish that has no brightness and looks like an older, worn piece.
E-coat: is an electrophoretic coating that provides maximum protection for anti-tarnish and extended wear. E-coat is not recommended for use with “88 metal”, a white cast metal which cannot withstand the e-coat’s curing cycle and will usually deform. The average e-coat thickness is usually less than 5 microns and covers the entire piece as it is electroplated.
Gold electroplate: as defined by the Federal Trade Commission is a deposit of a minimum of 7 millionths of an inch of gold
Gold flash: a short plating cycle (less than 15 seconds) that is used for color or thin deposits of less than 3 mils. A flash allows the plater a quick and inexpensive way to have a variety of gold colors (14kt. to 24kt.) as a final finish.
Green gold: is a colored gold finish that has a slight green hue due to the addition of silver as an alloy.
Hand antique: is an antique process where colored lacquer is applied over the surface of the piece, then removed by hand from the raised surfaces.
Heavy gold: as defined by the Federal Trade Commission is a deposit of 100 or more mils of gold.
Hollow objects: lightweight hollow items like hoop earrings or bracelets that trap solution when submerged can create problems in the plating process because the trap solution will cause staining or tarnishing. A drainage hole in the piece will usually prevent problems.
Hull-cell analysis: is a laboratory procedure that analyzes any bath by taking a small portion of the bath and plating from it. The laboratory technician then recommends additions which will improve the appearance of the plate.
Humidity testing: the purpose of humidity testing is to evaluate the performance and adhesion of the coating. The test takes place in a 100% humid chamber for 3-5 days.
Imitation Rhodium: a non-tarnishing, low cost white metal that has fair ware-ability.
Karat: indicates purity of deposit. 24kt consists of 100% gold; 18kt, 75% gold; and 14kt 58.3% gold.
Karat clad: indicates a heavy gold deposit, 100 mils, that is a composite metal of two or more layers that have been electrolytically bonded together.
Lacquer: is a paint, clear or colored, that is applied to an item.
Leveling: is the microscopic filling-in of surface imperfections that results in the surface being smoother and more level than before the procedure.
Matte: a dull, non-bright finish
Micron: 40 mils, or 40 millionths of an inch
Mil: a millionth of an inch
MIL spec: the standard military spec for plating is 60 millionth of an inch
Neutral Salt Spray test: the purpose of the NSS is to observe corrosion of the pre-plate and/or breakdown or lifting of the top coat. The test takes place in a chamber for either 100 hours (standard MIL spec.) or 336 hours G.M. exterior spec.
Nickel: is usually the layer between copper and the precious metal finish. Nickel protects metallic objects from corrosion and promotes excellent leveling. A bright nickel give high brightness to the final finish, and a Watts nickel produces a dull matte finish.
Nickel-free: is a type of hypo-allergenic plating. Generally, acid copper is substituted for nickel in the plating process, since about 10% of the population is susceptible to nickel allergies. Palladium is then used as a barrier coat between the copper and the top-coat.
Palladium: is a non-tarnishing precious metal that is often used as an alternative for rhodium, although it is not as white. Palladium is also used as a barrier coat in the nickel-free process.
Perspiration testing: a test using artificial perspiration that measures the ability of a coating to resist corrosion.
Physical Vapor Deposition (PVD or sputtering): A dry vacuum process used to coat parts with ultra-hard zirconium and titanium nitrides.
Plating: forming a layer of metal on an object from a plating solution.
Post-finishing: a procedure which is applied to an item after it is plated, for example, antique, chromate, or e-coat.
Powder coating: A clear or colored fine powder which is electrostatically applied dry and then cured in an oven to liquefy the powder and coat the entire item.
Pre-finishing: a procedure that is performed prior to plating to make the product suitable to receive the plate, for example, tubbing, vibing or polishing.
Rack plating: products are individually affixed, via a copper wire, to a plating rack. The rack is dipped into a plating bath, electric current is activated, and plating occurs.
Rhodium: an expensive, non-tarnishing, precious metal that has a good white color. Rhodium is a hard metal which provides good wear-resistance and is often used in two-tone finishes.
Rose gold: a colored gold finish which has a pink hue due to the addition of copper as an alloy.
Russian gold: is the same as smut gold
Satin: is a hand procedure which produces fine lines on an item prior to plating.
Satin-relieve: is a hand procedure which removes some top color and exposes the colored layer beneath. Satin-relieving leaves fine lines and produces a dull, antique look.
Silver: an inexpensive, beautiful, white metal. However, silver tarnishes and needs a protective coating.
Smut gold: is the addition of antimony to a gold bath to produce a black powdery finish that is easily removed with a mild abrasive to produce an antique finish.
Smut silver: is the chemical tarnishing of a silver deposit to produce a dark, oxide finish that is easily removed by a mild abrasive to produce an antique finish.
Stop-off: is the application of a plating resist to achieve a two-tone plating effect, usually gold and silver.
Tarni-tan: is a type of anti-tarnish protection
Thermal cycle testing: takes place in a computerized chamber where temperatures fluctuate from extreme hot to extreme cold over a long period of time (usually weeks). The plated finish or clear coat is evaluated for adhesion loss, cracks or fractures due to stressed deposit.
Thermal shock: is the rapid change in temperature from hot to cold or cold to hot. Thermal shock can cause certain stones to crack during the plating process.
Tubbing: is a pre-finish that is usually performed to brighten the item and takes place in a tub with detergent and steel shot.
Tumbling: is a pre-finish that takes place in a rotating barrel with abrasive medium.
Two-tone: is a plating process that produces a final finish that includes at least two different colors on the same piece.
Vermeil: as defined by the Federal Trade Commission is a deposit of 100 mils of gold over a silver product, with a nickel barrier between the silver base and the gold finish.
Vibing: is a pre-finishing technique that removes metal and improves the surface finish of an item by smoothing it.
X-ray fluorescence: is a non-destructive test to determine the thickness of various layers of metal on a part. Common elements measured are: copper, nickel, gold, silver, palladium and rhodium.